# 500 GB Webserver harddisk from lr-serv-01 # swap was on /dev/sda1 during installation # that works even if disks are added and removed. # device this may be used with UUID= as a more robust way to name devices # Use 'blkid' to print the universally unique identifier for a This is my fstab file: # /etc/fstab: static file system information. UUID=xxxxxxxxxxxxxxxxx /media/mydrivename ntfs permissions,locale=en_US.utf8 0 2 media/mydrivename is where the partition should be mounted. Next make a folder: sudo mkdir /media/mydrivenameĭon't forget to comment the output from the blkid with a '#' on the beginning of the lines!Īdd this to the fstab file, you can find the UUID in the block on the bottom you inserted with the command above. If you still screwed up you can replace your fstab with the original: sudo cp /etc/fstab.orig /etc/fstab Make sure you tripple check the >, if you place one > you overwrite your fstab! sudo blkid > /etc/fstab Make a back-up of your fstab file: sudo cp /etc/fstab /etc/fstab.orig I fixed the problem by mounting them by UUID in the fstab, you can view the UUID for your harddrives by entering: sudo blkid I had some trouble with this because when I reboot the disk name changes. You can disable fast startup by following these steps under "Power Options".
#Ntfs 3g etc fstab windows 8
This is because Windows 8 and 10 offer a "Fast Startup" option that depends on a "non-complete" shutdown. Please resume and shutdown Windows fully (no hibernation or fast restarting), or mount the volume read-only with the 'ro' mount option Metadata kept in Windows cache, refused to mount.įailed to mount '/dev/sda6': Operation not permitted The NTFS partition is in an unsafe state. If you get no visible error after rebooting and partitions stay readonly or you get an error similar to: Error mounting /dev/sda6 at /media/WindowsDrive:Ĭommand-line `mount -t "ntfs" -o "uhelper=udisks2,nodev,nosuid,uid=1000,gid=1000,dmask=0077,fmask=0177" "/dev/sda6" "/media/rolindroy/Media Center"' exited with non-zero exit status 14: The disk contains an unclean file system (0, 0). Here are two lines from my /etc/fstab working UUID=EEA2B69CA2B668AB /WIN_C ntfs-3g defaults,nls=utf8,umask=000,dmask=027,fmask=137,uid=1000,gid=1000,windows_names 0 0 This sets you as the owner of the drive, and sets the permissions to drwxr-x. These values are both usually 1000.Ī common set of mount options for ntfs is uid=1000,gid=1000,dmask=027,fmask=137. You can find your UID with the command id -u. To set the owner, use the uid and gid options for user and group, respectively. For example, rwx for the owner and rx for others is 022 rather than 755. Since these options set masks, they should be the complement of the permissions you want. dmask controls permissions for directories, fmask controls permissions for files, and umask controls both. To format a drive to Ext4 or NTFS on Windows smoothly, it is highly recommended you use MiniTool Partition Wizard.Permissions for ntfs and vfat file systems must be set with the dmask, fmask and umask options. In addition, these utilities have limitations on formatting a large capacity drive. Various benchmarks have concluded that the actual ext4 file system can perform a variety of read-write operations faster than an NTFS partition.Īlthough Microsoft Windows provides built-in utilities to format a drive to NTFS, they can’t help you format to Ext4. Step 4 – Find the Unique ID (UUID) of the formatted device for mounting.Step 3 – Create a mount point directory for the volume.Step 2 – Create an ext4 file system on the storage volume.
![ntfs 3g etc fstab ntfs 3g etc fstab](https://openrepos.net/sites/default/files/packages/5573/screenshot-ntfs-3g-demo-20150620.png)
Step 1 – Run lsblk to find your volume’s device name.Quick Start – for the Level 20 Linux mage Options – mount options (identical to those from the mount command).File system – The first column specifies the partition to be mounted.
#Ntfs 3g etc fstab how to
How to permanently mount partitions on Linux How do I permanently mount a filesystem in Linux? These partitions are normally formatted with NTFS, but are sometimes formatted with FAT32. Ubuntu is capable of reading and writing files stored on Windows formatted partitions. Add a line for the drive, the format would look like this. Be careful with this file as it can quite easily cause your system not to boot. You need to add it to /etc/fstab use your favourite text editor.
![ntfs 3g etc fstab ntfs 3g etc fstab](https://doxygen.reactos.org/d1/d8c/drivers_2filesystems_2ntfs_2ntfs_8c__incl.png)
Okay now you have a partition, now you need a filesystem.